Venetian Blind Size Calculator (Free Tool, 2026)

Made-to-measure Venetian blinds usually cannot be returned, so getting the size right matters. Enter your window measurements below and this free tool gives you the exact width and height to order for an inside or outside mount, plus an approximate slat count and a recess depth check for your slat size.

Free tool · Venetian blinds
Venetian Blind Size Calculator

Turn your window measurements into the exact blind size to order, plus slat count and recess depth check.

Tilt
1. Units
2. Mount type
3. Slat size
4. Width (in)
5. Height (in)
6. Recess depth
Order width
0
Order height
0
0Slats (approx.)
0Blind area
0Min. depth to fit flush
Read the full Venetian blinds guide →

Estimates only. Give the maker your exact measurements and follow their order form. Most companies deduct a small clearance for inside mounts themselves. Slat count and minimum depth vary by brand.

Embed This Venetian Blind Size Calculator on Your Site

Run a home improvement, smart home, contractor or real estate site? Add this free tool to any page. Copy the code below and paste it into an HTML block. It’s free, mobile-friendly and updates automatically.

Please keep the credit link below the tool. WordPress users: add a “Custom HTML” block and paste the code.

How to Use the Venetian Blind Size Calculator

  • Choose inches or centimeters and pick inside or outside mount.
  • Select the slat size you plan to buy. 50 mm (2 inch) is the most common for homes.
  • Enter the width at the top, middle and bottom, and the height on the left, center and right.
  • For an inside mount, add the depth of your window recess to check that the blind will fit flush.
  • Use the slider in the top corner to preview how the slats tilt.

How the Calculation Works

Inside mount: the tool uses the smallest width so the blind does not bind in the narrowest part of the recess, and the longest height so the blind reaches the sill everywhere. Outside mount: it adds about 3 inches (7.5 cm) on each side and above the opening, which is a common overlap for privacy and light control.

Slat count is estimated from the blind height and a slat spacing of roughly 85% of the slat width, because slats overlap slightly when closed. The minimum depth is a general guide; each brand lists its own number.

Minimum Recess Depth by Slat Size

Slat sizeApprox. depth to fit flushApprox. slats per 60″ blind
16 mm1.25 in (3.2 cm)112
25 mm (1″)1.75 in (4.4 cm)72
35 mm2.25 in (5.7 cm)52
50 mm (2″)2.75 in (7 cm)36
63 mm3.25 in (8.3 cm)29

Measuring Tips

  • Use a steel tape measure, not a cloth one.
  • Measure to the nearest 1/8 inch or 1 mm and write every number down.
  • Check for handles, window locks or tiles that could stop the slats hanging straight.
  • If you plan to add a smart tilt motor later, check that there is room at the top of the blind for it.

Frequently Asked Questions

How do I measure a window for Venetian blinds?

For an inside mount, measure the width inside the recess at the top, middle and bottom and use the smallest, then measure the height on the left, center and right and use the longest. For an outside mount, measure the opening and add about 3 inches (7.5 cm) on each side.

Should I deduct anything from my measurements?

Usually no. Most blind makers take off a small clearance for inside-mount blinds themselves. Give your exact measurements unless the order form tells you to deduct.

How deep does a window recess need to be for Venetian blinds?

It depends on the slat width and the brand. As a rough guide, 25 mm blinds need about 1.75 inches and 50 mm blinds about 2.75 inches to sit flush. Check the maker’s minimum before ordering.

How many slats will my blind have?

Slats are spaced a little closer than their width so they overlap when closed. A 60 inch tall blind with 50 mm slats has roughly 36 slats, while the same blind with 25 mm slats has about 72.

Is an inside or outside mount better?

Inside mount looks neater and shows off the window frame. Outside mount blocks more light and privacy gaps, hides out-of-square windows and works when the recess is too shallow.

Related Guides and Tools